DeVry NETW 204 Week 5 Quiz Latest

$20

Quantity:

Description

DeVry NETW 204 Week 5 Quiz Latest

 

1.Router_A is currently the OSPF designated router (DR). When will an election occur for a new DR? (Points : 2) When a new router comes up with a higher OSPF priority
When the point-to-point interface of the current DR goes down
When the DR fails
Answers A, B, and C are correct.
None of the above.

Question 2. 2.The 224.0.0.6 OSPF address is used by _____. (Points : 2)

all routers to exchange link state advertisement
only the designated router to advertise LSAs
both designated and backup designated routers to forward LSAs
DROther routers to send LSAs to DRs and BDRs
None of the above

 

Question 3. 3.An OSPF router is configured with a basic hello timer of 30 seconds. What will the default dead interval timer be? (Points : 2)

30 seconds
90 seconds
60 seconds
10 seconds
120 seconds

 

Question 4. 4.The OSPF packet header contains _____. (Points : 2)

the area priority field
the DROther field
the Type code for OSPF packet type
the router autonomous system field
Answers A and B are correct.

 

Question 5. 5.Which command will verify that a router that is running OSPFv2 has formed an adjacency with other routers in its OSPF area? (Points : 2)

show running-configuration
show ip ospf neighbor
show ipv6 ospf neighbor
show ipv6 route ospf
show ipv6 interface brief

 

Question 6. 6.Single area OSPFv3 has been enabled on a router via the ipv6 router ospf 15 command. Which command will enable this OSPFv3 process on an interface of that router? (Points : 2)

ipv6 ospf 0 area 0
ipv6 ospf 15 area 15
ipv6 ospf 0 area 0, 15
ipv6 ospf 15 area 0
None of the above

 

Question 7. 7.Which command will provide information specific to OSPFv3 routes in the routing table? (Points : 2)

show ip route ospf
show ip route ospfv3
show ipv6 route
show ip route ospf
show ipv6 route ospf

 

Question 8. 8.A network administrator enters the command ipv6 router ospf 64 in global configuration mode. What is the result of this command? (Points : 2)

The router will be assigned an autonomous system number of 64.
The router will be assigned a router ID of 64.
The reference bandwidth will be set to 64 Mb/s.
The OSPFv3 process will be assigned an ID of 64.
Answers A and C are correct.

 

Question 9. 9.Which command should be used in OSPF to provide detailed information about every OSPF-enabled interface? (Points : 2)

show ip protocols
show ip ospf neighbor
show ip ospf
show running-config
None of the above

 

Question 10. 10.A router in OSPF router has a data rate of 64 Kbps on one of its interfaces. What will the OSPF cost of that link be? (Points : 2)

110
1562
128
100
90

 

Question 11. 11.R1 is currently the DR router. R2 is currently the BDR router. R3 is currently the DROther. Your IT Manager has asked you to make R3 the DR and R2 the BDR. Which answer will achieve that goal? (Points : 2)

Change the priority number on R3 to be the highest.
Change the priority on R2 to be the second highest.
Answers A and B are correct.
Boot up R3 first followed by R2, and then R1.
Shutdown R3, R2, and R1 interfaces and bring them back up in the reverse order.

 

Question 12. 12.(TCO 5) Cisco’s routers use this first to determine router-ID in OSPF. Assume IP addresses are configured on physical and loopback Interfaces are working as expected. (Points : 3)

Largest loopback IP address
Largest physical Interface IP address
Lowest loopback IP address
Configured Router-ID
Both A and C are correct.

 

DeVry Courses helps in providing the best essay writing service. If you need 100% original papers for DeVry NETW 204 Week 5 Quiz Latest, then contact us through call or live chat.

DeVry NETW 204 Week 5 Quiz Latest

Best DeVry NETW 204 Week 5 Quiz Latest

DeVry NETW 204 Week 5 Quiz Latest